| 1 | == smartctl report about read failure for TOSHIBA THNSNJ256GVNU == |
| 2 | |
| 3 | === Command === |
| 4 | |
| 5 | {{{smartctl -x -q noserial ..}}} |
| 6 | |
| 7 | === Output === |
| 8 | |
| 9 | {{{ |
| 10 | smartctl 6.5 2016-05-07 r4318 [i686-w64-mingw32-win7] (sf-6.5-1) |
| 11 | Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org |
| 12 | |
| 13 | === START OF INFORMATION SECTION === |
| 14 | Device Model: TOSHIBA THNSNJ256GVNU |
| 15 | Firmware Version: JUTA0101 |
| 16 | User Capacity: 256,060,514,304 bytes [256 GB] |
| 17 | Sector Size: 512 bytes logical/physical |
| 18 | Rotation Rate: Solid State Device |
| 19 | Form Factor: < 1.8 inches |
| 20 | Device is: Not in smartctl database [for details use: -P showall] |
| 21 | ATA Version is: ACS-2 (minor revision not indicated) |
| 22 | SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) |
| 23 | Local Time is: Sun Mar 12 07:35:17 2017 PST |
| 24 | SMART support is: Available - device has SMART capability. |
| 25 | SMART support is: Enabled |
| 26 | AAM feature is: Unavailable |
| 27 | APM level is: 254 (maximum performance) |
| 28 | Rd look-ahead is: Enabled |
| 29 | Write cache is: Enabled |
| 30 | ATA Security is: Disabled, frozen [SEC2] |
| 31 | Wt Cache Reorder: Enabled |
| 32 | |
| 33 | === START OF READ SMART DATA SECTION === |
| 34 | SMART overall-health self-assessment test result: PASSED |
| 35 | |
| 36 | General SMART Values: |
| 37 | Offline data collection status: (0x02) Offline data collection activity |
| 38 | was completed without error. |
| 39 | Auto Offline Data Collection: Disabled. |
| 40 | Self-test execution status: ( 112) The previous self-test completed having |
| 41 | the read element of the test failed. |
| 42 | Total time to complete Offline |
| 43 | data collection: ( 120) seconds. |
| 44 | Offline data collection |
| 45 | capabilities: (0x5b) SMART execute Offline immediate. |
| 46 | Auto Offline data collection on/off support. |
| 47 | Suspend Offline collection upon new |
| 48 | command. |
| 49 | Offline surface scan supported. |
| 50 | Self-test supported. |
| 51 | No Conveyance Self-test supported. |
| 52 | Selective Self-test supported. |
| 53 | SMART capabilities: (0x0003) Saves SMART data before entering |
| 54 | power-saving mode. |
| 55 | Supports SMART auto save timer. |
| 56 | Error logging capability: (0x01) Error logging supported. |
| 57 | General Purpose Logging supported. |
| 58 | Short self-test routine |
| 59 | recommended polling time: ( 2) minutes. |
| 60 | Extended self-test routine |
| 61 | recommended polling time: ( 10) minutes. |
| 62 | SCT capabilities: (0x003d) SCT Status supported. |
| 63 | SCT Error Recovery Control supported. |
| 64 | SCT Feature Control supported. |
| 65 | SCT Data Table supported. |
| 66 | |
| 67 | SMART Attributes Data Structure revision number: 16 |
| 68 | Vendor Specific SMART Attributes with Thresholds: |
| 69 | ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE |
| 70 | 1 Raw_Read_Error_Rate -O-R-- 099 092 000 - 0 |
| 71 | 2 Throughput_Performance P-S--- 100 100 050 - 0 |
| 72 | 3 Spin_Up_Time POS--- 100 100 050 - 0 |
| 73 | 5 Reallocated_Sector_Ct PO--C- 100 100 050 - 0 |
| 74 | 7 Unknown_SSD_Attribute PO-R-- 100 100 050 - 0 |
| 75 | 8 Unknown_SSD_Attribute P-S--- 100 100 050 - 0 |
| 76 | 9 Power_On_Hours -O--C- 100 100 000 - 438 |
| 77 | 10 Unknown_SSD_Attribute PO--C- 100 100 050 - 0 |
| 78 | 12 Power_Cycle_Count -O--C- 100 100 000 - 287 |
| 79 | 167 Unknown_Attribute -O---K 100 100 000 - 0 |
| 80 | 168 Unknown_Attribute -O--C- 100 100 000 - 3 |
| 81 | 169 Unknown_Attribute PO--C- 100 100 010 - 100 |
| 82 | 170 Unknown_Attribute PO--C- 100 100 010 - 0 |
| 83 | 173 Unknown_Attribute PO--C- 200 200 100 - 0 |
| 84 | 175 Program_Fail_Count_Chip PO--C- 100 100 010 - 0 |
| 85 | 192 Power-Off_Retract_Count -O--C- 100 100 000 - 25 |
| 86 | 194 Temperature_Celsius -O---K 062 046 000 - 38 (Min/Max 18/54) |
| 87 | 197 Current_Pending_Sector -O--C- 100 100 000 - 0 |
| 88 | 240 Unknown_SSD_Attribute PO--C- 100 100 050 - 0 |
| 89 | ||||||_ K auto-keep |
| 90 | |||||__ C event count |
| 91 | ||||___ R error rate |
| 92 | |||____ S speed/performance |
| 93 | ||_____ O updated online |
| 94 | |______ P prefailure warning |
| 95 | |
| 96 | General Purpose Log Directory Version 1 |
| 97 | SMART Log Directory Version 1 [multi-sector log support] |
| 98 | Address Access R/W Size Description |
| 99 | 0x00 GPL,SL R/O 1 Log Directory |
| 100 | 0x01 SL R/O 1 Summary SMART error log |
| 101 | 0x02 SL R/O 51 Comprehensive SMART error log |
| 102 | 0x03 GPL R/O 64 Ext. Comprehensive SMART error log |
| 103 | 0x04 GPL,SL R/O 8 Device Statistics log |
| 104 | 0x06 SL R/O 1 SMART self-test log |
| 105 | 0x07 GPL R/O 1 Extended self-test log |
| 106 | 0x09 SL R/W 1 Selective self-test log |
| 107 | 0x10 GPL R/O 1 SATA NCQ Queued Error log |
| 108 | 0x11 GPL R/O 1 SATA Phy Event Counters log |
| 109 | 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log |
| 110 | 0x80-0x9f GPL,SL R/W 16 Host vendor specific log |
| 111 | 0xe0 GPL,SL R/W 1 SCT Command/Status |
| 112 | 0xe1 GPL,SL R/W 1 SCT Data Transfer |
| 113 | |
| 114 | SMART Extended Comprehensive Error Log Version: 1 (64 sectors) |
| 115 | Device Error Count: 65535 (device log contains only the most recent 256 errors) |
| 116 | CR = Command Register |
| 117 | FEATR = Features Register |
| 118 | COUNT = Count (was: Sector Count) Register |
| 119 | LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 |
| 120 | LH = LBA High (was: Cylinder High) Register ] LBA |
| 121 | LM = LBA Mid (was: Cylinder Low) Register ] Register |
| 122 | LL = LBA Low (was: Sector Number) Register ] |
| 123 | DV = Device (was: Device/Head) Register |
| 124 | DC = Device Control Register |
| 125 | ER = Error register |
| 126 | ST = Status register |
| 127 | Powered_Up_Time is measured from power on, and printed as |
| 128 | DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, |
| 129 | SS=sec, and sss=millisec. It "wraps" after 49.710 days. |
| 130 | |
| 131 | Error 65535 [118] occurred at disk power-on lifetime: 438 hours (18 days + 6 hours) |
| 132 | When the command that caused the error occurred, the device was active or idle. |
| 133 | |
| 134 | After command completion occurred, registers were: |
| 135 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
| 136 | -- -- -- == -- == == == -- -- -- -- -- |
| 137 | 40 -- 51 00 f0 00 00 01 8a a7 20 40 00 Error: UNC at LBA = 0x018aa720 = 25863968 |
| 138 | |
| 139 | Commands leading to the command that caused the error were: |
| 140 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
| 141 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
| 142 | 60 00 20 00 a0 00 00 01 d8 eb 8e 40 00 00:00:12.307 READ FPDMA QUEUED |
| 143 | 60 00 40 00 98 00 00 02 94 7f fa 40 00 00:00:12.307 READ FPDMA QUEUED |
| 144 | 61 00 08 00 90 00 00 1c 46 16 18 40 00 00:00:12.307 WRITE FPDMA QUEUED |
| 145 | 60 00 40 00 88 00 00 01 2d 9d 22 40 00 00:00:12.290 READ FPDMA QUEUED |
| 146 | 61 00 08 00 80 00 00 00 66 d1 38 40 00 00:00:12.290 WRITE FPDMA QUEUED |
| 147 | |
| 148 | Error 65534 [117] occurred at disk power-on lifetime: 438 hours (18 days + 6 hours) |
| 149 | When the command that caused the error occurred, the device was active or idle. |
| 150 | |
| 151 | After command completion occurred, registers were: |
| 152 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
| 153 | -- -- -- == -- == == == -- -- -- -- -- |
| 154 | 40 -- 51 00 10 00 00 01 8a a7 20 40 00 Error: WP at LBA = 0x018aa720 = 25863968 |
| 155 | |
| 156 | Commands leading to the command that caused the error were: |
| 157 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
| 158 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
| 159 | 61 00 08 00 d8 00 00 00 66 d1 40 40 00 00:00:12.183 WRITE FPDMA QUEUED |
| 160 | 61 00 48 00 d0 00 00 00 66 d3 30 40 00 00:00:12.183 WRITE FPDMA QUEUED |
| 161 | 60 00 08 00 c8 00 00 00 6b 0a 78 40 00 00:00:12.132 READ FPDMA QUEUED |
| 162 | 60 00 08 00 c0 00 00 00 a1 e5 10 40 00 00:00:12.100 READ FPDMA QUEUED |
| 163 | 61 00 01 00 b8 00 00 00 b8 9d 58 40 00 00:00:12.045 WRITE FPDMA QUEUED |
| 164 | |
| 165 | Error 65533 [116] occurred at disk power-on lifetime: 438 hours (18 days + 6 hours) |
| 166 | When the command that caused the error occurred, the device was active or idle. |
| 167 | |
| 168 | After command completion occurred, registers were: |
| 169 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
| 170 | -- -- -- == -- == == == -- -- -- -- -- |
| 171 | 40 -- 51 00 48 00 00 01 8a a7 20 40 00 Error: UNC at LBA = 0x018aa720 = 25863968 |
| 172 | |
| 173 | Commands leading to the command that caused the error were: |
| 174 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
| 175 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
| 176 | 60 00 20 00 f0 00 00 02 1c 7a c8 40 00 00:00:11.900 READ FPDMA QUEUED |
| 177 | 60 00 08 00 e8 00 00 02 94 87 64 40 00 00:00:11.885 READ FPDMA QUEUED |
| 178 | 60 00 08 00 d8 00 00 00 6c 9f 20 40 00 00:00:11.884 READ FPDMA QUEUED |
| 179 | 60 00 08 00 d0 00 00 02 7a d3 08 40 00 00:00:11.884 READ FPDMA QUEUED |
| 180 | 60 00 40 00 c8 00 00 03 33 4a 20 40 00 00:00:11.884 READ FPDMA QUEUED |
| 181 | |
| 182 | Error 65532 [115] occurred at disk power-on lifetime: 438 hours (18 days + 6 hours) |
| 183 | When the command that caused the error occurred, the device was active or idle. |
| 184 | |
| 185 | After command completion occurred, registers were: |
| 186 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
| 187 | -- -- -- == -- == == == -- -- -- -- -- |
| 188 | 40 -- 51 00 70 00 00 01 8a a7 20 40 00 Error: UNC at LBA = 0x018aa720 = 25863968 |
| 189 | |
| 190 | Commands leading to the command that caused the error were: |
| 191 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
| 192 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
| 193 | 60 00 03 00 20 00 00 03 1f d5 dd 40 00 00:00:11.859 READ FPDMA QUEUED |
| 194 | 60 00 05 00 18 00 00 03 35 3a 00 40 00 00:00:11.545 READ FPDMA QUEUED |
| 195 | 60 00 18 00 10 00 00 03 33 5d 15 40 00 00:00:11.529 READ FPDMA QUEUED |
| 196 | 60 00 08 00 08 00 00 00 68 ea 10 40 00 00:00:11.528 READ FPDMA QUEUED |
| 197 | 60 00 08 00 00 00 00 02 4d 3f b8 40 00 00:00:11.527 READ FPDMA QUEUED |
| 198 | |
| 199 | Error 65531 [114] occurred at disk power-on lifetime: 438 hours (18 days + 6 hours) |
| 200 | When the command that caused the error occurred, the device was active or idle. |
| 201 | |
| 202 | After command completion occurred, registers were: |
| 203 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
| 204 | -- -- -- == -- == == == -- -- -- -- -- |
| 205 | 40 -- 51 00 30 00 00 01 8a a7 20 40 00 Error: UNC at LBA = 0x018aa720 = 25863968 |
| 206 | |
| 207 | Commands leading to the command that caused the error were: |
| 208 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
| 209 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
| 210 | 60 00 40 00 00 00 00 01 73 07 d2 40 00 00:00:11.463 READ FPDMA QUEUED |
| 211 | 60 00 b4 00 f8 00 00 01 e1 6b 60 40 00 00:00:11.462 READ FPDMA QUEUED |
| 212 | 60 00 08 00 f0 00 00 02 1c 77 20 40 00 00:00:11.462 READ FPDMA QUEUED |
| 213 | 60 00 08 00 e0 00 00 00 6a 14 30 40 00 00:00:11.462 READ FPDMA QUEUED |
| 214 | 60 00 08 00 c8 00 00 03 01 01 00 40 00 00:00:11.462 READ FPDMA QUEUED |
| 215 | |
| 216 | Error 65530 [113] occurred at disk power-on lifetime: 438 hours (18 days + 6 hours) |
| 217 | When the command that caused the error occurred, the device was active or idle. |
| 218 | |
| 219 | After command completion occurred, registers were: |
| 220 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
| 221 | -- -- -- == -- == == == -- -- -- -- -- |
| 222 | 40 -- 51 00 20 00 00 01 8a a7 20 40 00 Error: UNC at LBA = 0x018aa720 = 25863968 |
| 223 | |
| 224 | Commands leading to the command that caused the error were: |
| 225 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
| 226 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
| 227 | 60 00 20 00 28 00 00 03 33 5f 75 40 00 00:00:11.430 READ FPDMA QUEUED |
| 228 | 60 00 40 00 18 00 00 00 21 f6 92 40 00 00:00:11.430 READ FPDMA QUEUED |
| 229 | 60 00 20 00 10 00 00 01 2d bb 28 40 00 00:00:11.229 READ FPDMA QUEUED |
| 230 | 60 00 40 00 08 00 00 01 73 05 e0 40 00 00:00:11.122 READ FPDMA QUEUED |
| 231 | 60 00 40 00 00 00 00 00 3d 9d 60 40 00 00:00:11.122 READ FPDMA QUEUED |
| 232 | |
| 233 | Error 65529 [112] occurred at disk power-on lifetime: 438 hours (18 days + 6 hours) |
| 234 | When the command that caused the error occurred, the device was active or idle. |
| 235 | |
| 236 | After command completion occurred, registers were: |
| 237 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
| 238 | -- -- -- == -- == == == -- -- -- -- -- |
| 239 | 40 -- 51 00 f8 00 00 01 8a a7 20 40 00 Error: UNC at LBA = 0x018aa720 = 25863968 |
| 240 | |
| 241 | Commands leading to the command that caused the error were: |
| 242 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
| 243 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
| 244 | 60 00 40 00 10 00 00 01 25 a3 a2 40 00 00:00:15.867 READ FPDMA QUEUED |
| 245 | 60 00 80 00 08 00 00 01 93 63 88 40 00 00:00:15.850 READ FPDMA QUEUED |
| 246 | 60 00 08 00 00 00 00 00 6c c4 48 40 00 00:00:15.850 READ FPDMA QUEUED |
| 247 | 60 00 08 00 f8 00 00 01 8a a7 20 40 00 00:00:15.850 READ FPDMA QUEUED |
| 248 | 60 00 18 00 f0 00 00 01 25 60 1a 40 00 00:00:15.850 READ FPDMA QUEUED |
| 249 | |
| 250 | Error 65528 [111] occurred at disk power-on lifetime: 438 hours (18 days + 6 hours) |
| 251 | When the command that caused the error occurred, the device was active or idle. |
| 252 | |
| 253 | After command completion occurred, registers were: |
| 254 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
| 255 | -- -- -- == -- == == == -- -- -- -- -- |
| 256 | 40 -- 51 00 70 00 00 01 8a a7 20 40 00 Error: UNC at LBA = 0x018aa720 = 25863968 |
| 257 | |
| 258 | Commands leading to the command that caused the error were: |
| 259 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
| 260 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
| 261 | 60 00 03 00 d8 00 00 00 f6 92 b7 40 00 00:00:15.821 READ FPDMA QUEUED |
| 262 | 60 00 08 00 d0 00 00 01 93 63 80 40 00 00:00:15.821 READ FPDMA QUEUED |
| 263 | 60 00 28 00 c8 00 00 04 dc 35 3a 40 00 00:00:15.821 READ FPDMA QUEUED |
| 264 | 60 00 20 00 c0 00 00 01 25 ac 13 40 00 00:00:15.621 READ FPDMA QUEUED |
| 265 | 61 00 01 00 b8 00 00 00 22 fc f8 40 00 00:00:15.587 WRITE FPDMA QUEUED |
| 266 | |
| 267 | SMART Extended Self-test Log Version: 1 (1 sectors) |
| 268 | Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error |
| 269 | # 1 Short offline Completed: read failure 00% 406 635416 |
| 270 | # 2 Short offline Completed without error 00% 371 - |
| 271 | # 3 Short offline Completed without error 00% 274 - |
| 272 | # 4 Short offline Completed without error 00% 202 - |
| 273 | # 5 Short offline Completed without error 00% 109 - |
| 274 | |
| 275 | SMART Selective self-test log data structure revision number 1 |
| 276 | SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS |
| 277 | 1 0 0 Not_testing |
| 278 | 2 0 0 Not_testing |
| 279 | 3 0 0 Not_testing |
| 280 | 4 0 0 Not_testing |
| 281 | 5 0 0 Not_testing |
| 282 | Selective self-test flags (0x0): |
| 283 | After scanning selected spans, do NOT read-scan remainder of disk. |
| 284 | If Selective self-test is pending on power-up, resume after 0 minute delay. |
| 285 | |
| 286 | SCT Status Version: 3 |
| 287 | SCT Version (vendor specific): 3 (0x0003) |
| 288 | SCT Support Level: 0 |
| 289 | Device State: Active (0) |
| 290 | Current Temperature: 38 Celsius |
| 291 | Power Cycle Min/Max Temperature: 24/38 Celsius |
| 292 | Lifetime Min/Max Temperature: 18/54 Celsius |
| 293 | Under/Over Temperature Limit Count: 0/0 |
| 294 | Vendor specific: |
| 295 | 00 00 04 00 01 01 00 05 05 00 00 00 00 00 00 00 |
| 296 | 00 01 00 00 f4 13 18 00 02 02 00 00 00 00 00 06 |
| 297 | |
| 298 | SCT Temperature History Version: 2 |
| 299 | Temperature Sampling Period: 1 minute |
| 300 | Temperature Logging Interval: 1 minute |
| 301 | Min/Max recommended Temperature: 5/40 Celsius |
| 302 | Min/Max Temperature Limit: 0/80 Celsius |
| 303 | Temperature History Size (Index): 128 (0) |
| 304 | |
| 305 | Index Estimated Time Temperature Celsius |
| 306 | 1 2017-03-12 05:28 43 ************************ |
| 307 | ... ..(112 skipped). .. ************************ |
| 308 | 114 2017-03-12 07:21 43 ************************ |
| 309 | 115 2017-03-12 07:22 ? - |
| 310 | 116 2017-03-12 07:23 27 ******** |
| 311 | 117 2017-03-12 07:24 ? - |
| 312 | ... ..( 2 skipped). .. - |
| 313 | 120 2017-03-12 07:27 ? - |
| 314 | 121 2017-03-12 07:28 32 ************* |
| 315 | 122 2017-03-12 07:29 34 *************** |
| 316 | 123 2017-03-12 07:30 35 **************** |
| 317 | 124 2017-03-12 07:31 36 ***************** |
| 318 | 125 2017-03-12 07:32 37 ****************** |
| 319 | 126 2017-03-12 07:33 37 ****************** |
| 320 | 127 2017-03-12 07:34 38 ******************* |
| 321 | 0 2017-03-12 07:35 38 ******************* |
| 322 | |
| 323 | SCT Error Recovery Control: |
| 324 | Read: 600 (60.0 seconds) |
| 325 | Write: 600 (60.0 seconds) |
| 326 | |
| 327 | Device Statistics (GP Log 0x04) |
| 328 | Page Offset Size Value Flags Description |
| 329 | 0x01 ===== = = === == General Statistics (rev 2) == |
| 330 | 0x01 0x008 4 287 --- Lifetime Power-On Resets |
| 331 | 0x01 0x018 6 1480544217 --- Logical Sectors Written |
| 332 | 0x01 0x020 6 24980205 --- Number of Write Commands |
| 333 | 0x01 0x028 6 1579365109 --- Logical Sectors Read |
| 334 | 0x01 0x030 6 27722663 --- Number of Read Commands |
| 335 | 0x04 ===== = = === == General Errors Statistics (rev 1) == |
| 336 | 0x04 0x008 4 132980 --- Number of Reported Uncorrectable Errors |
| 337 | 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion |
| 338 | 0x05 ===== = = === == Temperature Statistics (rev 1) == |
| 339 | 0x05 0x008 1 38 --- Current Temperature |
| 340 | 0x05 0x010 1 30 --- Average Short Term Temperature |
| 341 | 0x05 0x018 1 - --- Average Long Term Temperature |
| 342 | 0x05 0x020 1 52 --- Highest Temperature |
| 343 | 0x05 0x028 1 23 --- Lowest Temperature |
| 344 | 0x05 0x030 1 41 --- Highest Average Short Term Temperature |
| 345 | 0x05 0x038 1 25 --- Lowest Average Short Term Temperature |
| 346 | 0x05 0x040 1 - --- Highest Average Long Term Temperature |
| 347 | 0x05 0x048 1 - --- Lowest Average Long Term Temperature |
| 348 | 0x05 0x050 4 1400 --- Time in Over-Temperature |
| 349 | 0x05 0x058 1 40 --- Specified Maximum Operating Temperature |
| 350 | 0x05 0x060 4 0 --- Time in Under-Temperature |
| 351 | 0x05 0x068 1 5 --- Specified Minimum Operating Temperature |
| 352 | 0x06 ===== = = === == Transport Statistics (rev 1) == |
| 353 | 0x06 0x008 4 673 --- Number of Hardware Resets |
| 354 | 0x06 0x018 4 3 --- Number of Interface CRC Errors |
| 355 | 0x07 ===== = = === == Solid State Device Statistics (rev 1) == |
| 356 | 0x07 0x008 1 0 N-- Percentage Used Endurance Indicator |
| 357 | |||_ C monitored condition met |
| 358 | ||__ D supports DSN |
| 359 | |___ N normalized value |
| 360 | |
| 361 | SATA Phy Event Counters (GP Log 0x11) |
| 362 | ID Size Value Description |
| 363 | 0x0001 2 0 Command failed due to ICRC error |
| 364 | 0x0002 4 0 R_ERR response for data FIS |
| 365 | 0x0003 2 0 R_ERR response for device-to-host data FIS |
| 366 | 0x0004 2 0 R_ERR response for host-to-device data FIS |
| 367 | 0x0005 4 0 R_ERR response for non-data FIS |
| 368 | 0x0006 2 0 R_ERR response for device-to-host non-data FIS |
| 369 | 0x0007 2 0 R_ERR response for host-to-device non-data FIS |
| 370 | 0x0008 2 0 Device-to-host non-data FIS retries |
| 371 | 0x0009 4 4 Transition from drive PhyRdy to drive PhyNRdy |
| 372 | 0x000a 4 5 Device-to-host register FISes sent due to a COMRESET |
| 373 | 0x000b 4 0 CRC errors within host-to-device FIS |
| 374 | 0x000d 4 0 Non-CRC errors within host-to-device FIS |
| 375 | 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC |
| 376 | 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC |
| 377 | 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC |
| 378 | 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC |
| 379 | }}} |
| 380 | |
| 381 | == License == |
| 382 | |
| 383 | Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.3 or any later version published by the Free Software Foundation; |
| 384 | |
| 385 | For an online copy of the license see https://www.gnu.org/licenses/fdl.html |