smartctl report for HTS547550A9E384
Command
Access via AHCI controller: smartctl -x -q noserial ..
Output
smartctl 6.5 2016-05-07 r4318 [FreeBSD 10.3-RELEASE-p16 amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi/HGST Travelstar 5K750
Device Model: Hitachi HTS547550A9E384
Firmware Version: JE3OA40J
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Tue Mar 14 15:19:01 2017 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 45) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 152) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0
2 Throughput_Performance P-S--- 197 197 040 - 160
3 Spin_Up_Time POS--- 211 211 033 - 1
4 Start_Stop_Count -O--C- 100 100 000 - 59
5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0
7 Seek_Error_Rate PO-R-- 100 100 067 - 0
8 Seek_Time_Performance P-S--- 120 120 040 - 32
9 Power_On_Hours -O--C- 001 001 000 - 53400
10 Spin_Retry_Count PO--C- 100 100 060 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 58
191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0
192 Power-Off_Retract_Count -O--CK 100 100 000 - 9
193 Load_Cycle_Count -O--C- 001 001 000 - 14907336
194 Temperature_Celsius -O---- 222 222 000 - 27 (Min/Max 12/48)
196 Reallocated_Event_Count -O--CK 100 100 000 - 1
197 Current_Pending_Sector -O---K 100 100 000 - 0
198 Offline_Uncorrectable ---R-- 100 100 000 - 0
199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0
223 Load_Retry_Count -O-R-- 100 100 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 1 Comprehensive SMART error log
0x03 GPL R/O 1 Ext. Comprehensive SMART error log
0x04 GPL R/O 7 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Device Error Count: 1
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 [0] occurred at disk power-on lifetime: 1 hours (0 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
02 -- 51 00 00 00 00 00 00 00 00 00 00 Error: TK0NF
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
10 00 00 00 01 00 00 00 00 03 34 e0 ff 00:00:17.305 RECALIBRATE [OBS-4]
10 00 00 00 01 00 00 00 00 03 34 e0 08 00:00:17.138 RECALIBRATE [OBS-4]
91 40 00 01 3f 00 00 01 00 03 34 af 08 00:00:17.138 INITIALIZE DEVICE PARAMETERS [OBS-6]
c4 00 40 00 00 00 00 3f 00 00 00 e0 04 00:00:16.934 READ MULTIPLE
c4 00 40 00 01 00 00 3f 00 00 00 e0 00 00:00:07.959 READ MULTIPLE
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 43116 -
# 2 Extended offline Completed without error 00% 29867 -
# 3 Extended offline Completed without error 00% 19477 -
# 4 Extended offline Completed without error 00% 13675 -
# 5 Extended offline Completed without error 00% 10202 -
# 6 Extended offline Completed without error 00% 5334 -
# 7 Extended offline Completed without error 00% 4764 -
# 8 Extended offline Completed without error 00% 2322 -
# 9 Extended offline Completed without error 00% 25 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 27 Celsius
Power Cycle Min/Max Temperature: 15/38 Celsius
Lifetime Min/Max Temperature: 12/48 Celsius
Lifetime Average Temperature: 26 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 15 minutes
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -40/65 Celsius
Temperature History Size (Index): 128 (94)
Index Estimated Time Temperature Celsius
95 2017-03-13 07:30 26 *******
96 2017-03-13 07:45 25 ******
97 2017-03-13 08:00 26 *******
98 2017-03-13 08:15 25 ******
99 2017-03-13 08:30 25 ******
100 2017-03-13 08:45 26 *******
... ..( 9 skipped). .. *******
110 2017-03-13 11:15 26 *******
111 2017-03-13 11:30 27 ********
112 2017-03-13 11:45 27 ********
113 2017-03-13 12:00 26 *******
114 2017-03-13 12:15 26 *******
115 2017-03-13 12:30 27 ********
116 2017-03-13 12:45 26 *******
... ..( 2 skipped). .. *******
119 2017-03-13 13:30 26 *******
120 2017-03-13 13:45 27 ********
121 2017-03-13 14:00 26 *******
122 2017-03-13 14:15 26 *******
123 2017-03-13 14:30 26 *******
124 2017-03-13 14:45 27 ********
125 2017-03-13 15:00 26 *******
126 2017-03-13 15:15 26 *******
127 2017-03-13 15:30 27 ********
0 2017-03-13 15:45 27 ********
1 2017-03-13 16:00 26 *******
2 2017-03-13 16:15 27 ********
3 2017-03-13 16:30 27 ********
4 2017-03-13 16:45 27 ********
5 2017-03-13 17:00 26 *******
6 2017-03-13 17:15 26 *******
7 2017-03-13 17:30 26 *******
8 2017-03-13 17:45 27 ********
... ..( 6 skipped). .. ********
15 2017-03-13 19:30 27 ********
16 2017-03-13 19:45 26 *******
17 2017-03-13 20:00 26 *******
18 2017-03-13 20:15 26 *******
19 2017-03-13 20:30 27 ********
20 2017-03-13 20:45 27 ********
21 2017-03-13 21:00 26 *******
22 2017-03-13 21:15 27 ********
23 2017-03-13 21:30 27 ********
24 2017-03-13 21:45 26 *******
... ..( 3 skipped). .. *******
28 2017-03-13 22:45 26 *******
29 2017-03-13 23:00 27 ********
30 2017-03-13 23:15 26 *******
31 2017-03-13 23:30 27 ********
32 2017-03-13 23:45 26 *******
33 2017-03-14 00:00 26 *******
34 2017-03-14 00:15 26 *******
35 2017-03-14 00:30 27 ********
36 2017-03-14 00:45 27 ********
37 2017-03-14 01:00 27 ********
38 2017-03-14 01:15 26 *******
39 2017-03-14 01:30 26 *******
40 2017-03-14 01:45 27 ********
41 2017-03-14 02:00 26 *******
... ..( 8 skipped). .. *******
50 2017-03-14 04:15 26 *******
51 2017-03-14 04:30 27 ********
52 2017-03-14 04:45 26 *******
... ..( 36 skipped). .. *******
89 2017-03-14 14:00 26 *******
90 2017-03-14 14:15 27 ********
91 2017-03-14 14:30 26 *******
92 2017-03-14 14:45 27 ********
93 2017-03-14 15:00 26 *******
94 2017-03-14 15:15 27 ********
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 1) ==
0x01 0x008 4 58 --- Lifetime Power-On Resets
0x01 0x010 4 53400 --- Power-on Hours
0x01 0x018 6 10920695850 --- Logical Sectors Written
0x01 0x020 6 190751879 --- Number of Write Commands
0x01 0x028 6 11545163847 --- Logical Sectors Read
0x01 0x030 6 39023365 --- Number of Read Commands
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 17557 --- Spindle Motor Power-on Hours
0x03 0x010 4 16408 --- Head Flying Hours
0x03 0x018 4 14907336 --- Head Load Events
0x03 0x020 4 0 --- Number of Reallocated Logical Sectors
0x03 0x028 4 4070 --- Read Recovery Attempts
0x03 0x030 4 3 --- Number of Mechanical Start Failures
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 358 --- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 27 --- Current Temperature
0x05 0x010 1 26 N-- Average Short Term Temperature
0x05 0x018 1 25 N-- Average Long Term Temperature
0x05 0x020 1 48 --- Highest Temperature
0x05 0x028 1 12 --- Lowest Temperature
0x05 0x030 1 40 N-- Highest Average Short Term Temperature
0x05 0x038 1 14 N-- Lowest Average Short Term Temperature
0x05 0x040 1 38 N-- Highest Average Long Term Temperature
0x05 0x048 1 23 N-- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 60 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 0 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 507 --- Number of Hardware Resets
0x06 0x010 4 288 --- Number of ASR Events
0x06 0x018 4 0 --- Number of Interface CRC Errors
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0009 2 62 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 46 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
Last modified
8 years ago
Last modified on Mar 18, 2017, 11:00:34 PM
Note:
See TracWiki
for help on using the wiki.
