Opened 8 months ago
Last modified 5 weeks ago
#1814 new enhancement
please add support for Micron CT1000X9SSD9 (0x0634:0x5605)
| Reported by: | void | Owned by: | |
|---|---|---|---|
| Priority: | minor | Milestone: | undecided |
| Component: | drivedb | Version: | 7.4 |
| Keywords: | usb nand | Cc: | void |
Description (last modified by )
This SSD us badged as Crucial X9 1TB Portable External SSD
os: FreeBSD-14.0-p5 arm64
# smartctl -x -d sat,auto /dev/da0
smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.0-RELEASE-p5 arm64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: Micron
Product: CT1000X9SSD9
Revision: PMAP
Compliance: SPC-4
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Logical block size: 512 bytes
LU is fully provisioned [LBPRZ=1]
scsiModePageOffset: response length too short, resp_len=4 offset=4 bd_len=0
Logical Unit id: 0x500014a000000001
Device type: disk
scsiModePageOffset: response length too short, resp_len=4 offset=4 bd_len=0
Local Time is: Mon Mar 18 13:36:26 2024
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Disabled or Not Supported
Read Cache is: Enabled
Writeback Cache is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Current Drive Temperature: 0 C
Drive Trip Temperature: 0 C
Read defect list: asked for grown list but didn't get it
Error Counter logging not supported
scsiModePageOffset: response length too short, resp_len=4 offset=4 bd_len=0
Device does not support Self Test logging
Device does not support Background scan results logging
Device does not support General statistics and performance logging
###
# lsusb -v -d 0634:5605 | less
Bus /dev/usb Device /dev/ugen0.4: ID 0634:5605 Micron Technology, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.20
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 9
idVendor 0x0634 Micron Technology, Inc.
idProduct 0x5605
bcdDevice 1.10
iManufacturer 1 Micron
iProduct 2 CT1000X9SSD9
iSerial 3 [redacted]
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 121
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 224mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 8
Endpoint Descriptor:
:can't get debug descriptor: Input/output error
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 8
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 1
bNumEndpoints 4
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 98
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 8
MaxStreams 32
INTERFACE CLASS: 04 24 03 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 8
MaxStreams 32
INTERFACE CLASS: 04 24 04 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 1
MaxStreams 32
INTERFACE CLASS: 04 24 02 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 16
INTERFACE CLASS: 04 24 01 00
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 42
bNumDeviceCaps 3
USB 2.0 Extension Device Capability:
bLength 7
bDescriptorType 16
bDevCapabilityType 2
bmAttributes 0x00000006
Link Power Management (LPM) Supported
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
bmAttributes 0x00
Latency Tolerance Messages (LTM) Supported
wSpeedsSupported 0x000e
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 0
Lowest fully-functional device speed is Low Speed (1Mbps)
bU1DevExitLat 2 micro seconds
bU2DevExitLat 2815 micro seconds
** UNRECOGNIZED: 14 10 0a 00 01 00 00 00 00 11 00 00 30 40 0a 00 b0 40 0a 00
Change History (6)
comment:1 by , 8 months ago
| Description: | modified (diff) |
|---|
comment:2 by , 8 months ago
| Component: | all → drivedb |
|---|---|
| Keywords: | usb added |
| Milestone: | → undecided |
comment:3 by , 8 months ago
Hi,
Sorry for the delay - the system has since been re-installed.
Here is the smartctl output from your suggested input:
# smartctl -x -d sat /dev/da0 smartctl 7.4 2023-08-01 r5530 [FreeBSD 15.0-CURRENT arm64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org Read Device Identity failed: Input/output error If this is a USB connected device, look at the various --device=TYPE variants A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.
comment:4 by , 8 months ago
Some more testing:
/usr/local/share/smartmontools/drivedb.h 7.3/5528 updated to 7.3/5610
# smartctl -x -d sat -T verypermissive /dev/da0
smartctl 7.4 2023-08-01 r5530 [FreeBSD 15.0-CURRENT arm64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
Read Device Identity failed: Input/output error
If this is a USB connected device, look at the various --device=TYPE variants
START OF INFORMATION SECTION
Device Model: ������
Serial Number: }AR�����
Firmware Version: ���
Rotation Rate: 43551 rpm
Form Factor: 1.8 inches
Zoned Device: Host Aware Zones
Device is: Not in smartctl database 7.3/5610
ATA Version is: ACS >5 (15) (unknown minor revision code: 0x9100)
SATA Version is: SATA 3.3, >6.0 Gb/s (7)
Local Time is: Mon Apr 8 11:53:17 2024
SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 82-83 don't show if SMART supported.
SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 85-87 don't show if SMART is enabled.
Checking to be sure by trying SMART RETURN STATUS command.
SMART support is: Unknown - Try option -s with argument 'on' to enable it.AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Unavailable
Write cache is: Unavailable
DSN feature is: Unavailable
ATA Security is: ENABLED, PW level MAX, not locked, not frozen [SEC5], Master PW ID: 0x03e7
Read SCT Status failed: Input/output error
Wt Cache Reorder: Unknown (SCT Feature Control command failed)
Read SMART Data failed: Input/output error
START OF READ SMART DATA SECTION
SMART Status command failed: scsi error unsupported scsi opcode
SMART overall-health self-assessment test result: UNKNOWN!
SMART Status, Attributes and Thresholds cannot be read.
Read SMART Log Directory failed: Input/output error
ATA_READ_LOG_EXT (addr=0x00:0x00, page=0, n=1) failed: Input/output error
Read GP Log Directory failed
SMART Extended Comprehensive Error Log (GP Log 0x03) not supported
Read SMART Error Log failed: Input/output error
SMART Extended Self-test Log (GP Log 0x07) not supported
Read SMART Self-test Log failed: Input/output error
Selective Self-tests/Logging not supported
Read SCT Status failed: Input/output error
Read SCT Status failed: Input/output error
SCT (Get) Error Recovery Control command failed
Device Statistics (GP/SMART Log 0x04) not supported
Pending Defects log (GP Log 0x0c) not supported
ATA_READ_LOG_EXT (addr=0x11:0x00, page=0, n=1) failed: Input/output error
Read SATA Phy Event Counters failed
comment:5 by , 8 months ago
| Summary: | please add support for Micron CT1000X9SSD9 → please add support for Micron CT1000X9SSD9 (0x0634:0x5605) |
|---|
-d sat is neither supported nor correctly rejected (with unsupported scsi opcode).
If none of the other -d usb* or -d snt* options (see USB wiki page) work, we could only add this USB Id as unsupported.
Note that this device may use an USB->NAND controller without any ATA- or NVMe-like diagnostics. See ticket #1767 for another example which has some ATA diagnostic support.
PS: In future submissions, please use proper wiki markup for smartctl output.
comment:6 by , 5 weeks ago
| Keywords: | nand added |
|---|
The
autoflag checks for"ATA "in SCSI VENDOR field. This works with SAT layers of SCSI/SAS controllers but never with USB devices which return the real vendor.Please retry with
smartctl -x -d sat /dev/da0.