Opened 20 months ago
Closed 20 months ago
#1725 closed enhancement (duplicate)
NVMe pass-through support for Argon ONE M.2 Expansion Board (NVME)
| Reported by: | RobertCezar | Owned by: | |
|---|---|---|---|
| Priority: | minor | Milestone: | Release 7.3 |
| Component: | all | Version: | 7.2 |
| Keywords: | nvme usb | Cc: |
Description
I tried to get info of Argon ONE M.2 Expansion Board (NVME), but got this error (I had to specify -d scsi by trial and error otherwise got error)
sudo smartctl /dev/sdb smartctl 7.2 2020-12-30 r5155 [aarch64-linux-6.1.21-v8+] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org /dev/sdb: Unknown SNT device type 'sntasmedia' Please specify device type with the -d option. Use smartctl -h to get a usage summary
sudo smartctl -a -d scsi /dev/sdb smartctl 7.2 2020-12-30 r5155 [aarch64-linux-6.1.21-v8+] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: Argon Product: Forty Revision: 0 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: Solid State Device Logical Unit id: 0x5000000000000001 Serial number: 50F000000000 Device type: disk Local Time is: Sat May 13 10:38:14 2023 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 0 C Drive Trip Temperature: 0 C Error Counter logging not supported Device does not support Self Test logging
sudo smartctl -a -d sntrealtek /dev/sdb -r ioctl,2 smartctl 7.2 2020-12-30 r5155 [aarch64-linux-6.1.21-v8+] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org [NVMe call: opcode=0x06, size=0x1000, nsid=0x00000000, cdw10=0x00000001] >>>> do_scsi_cmnd_io: sg_io_ver=3 [<vendor specific>: e4 00 10 06 01 00 00 00 00 00 00 00 00 00 00 00 ] scsi_status=0x0, sg_transport_status=0x0, sg_driver_status=0x0 sg_info=0x0 sg_duration=0 milliseconds resid=4096 Incoming data trimmed to nothing by resid [NVMe call succeeded: result=0x00000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ ... ] === START OF INFORMATION SECTION === Model Number: Serial Number: Firmware Version: PCI Vendor ID: 0x0000 PCI Vendor Subsystem ID: 0x0000 IEEE OUI Identifier: 0x000000 Total NVM Capacity: 0 Unallocated NVM Capacity: 0 Controller ID: 0 NVMe Version: <1.2 Number of Namespaces: 0 Local Time is: Sat May 13 10:41:39 2023 EEST Firmware Updates (0x00): 0 Slots Optional Admin Commands (0x0000): - Optional NVM Commands (0x0000): - Log Page Attributes (0x00): - Maximum Data Transfer Size: - Warning Comp. Temp. Threshold: - Critical Comp. Temp. Threshold: - Namespace 4294967295 Features (0x00): - Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 0.00W - - 0 0 0 0 0 0 === START OF SMART DATA SECTION === [NVMe call: opcode=0x02, size=0x0200, nsid=0xffffffff, cdw10=0x007f0002] >>>> do_scsi_cmnd_io: sg_io_ver=3 [<vendor specific>: e4 00 02 02 02 00 00 00 00 00 00 00 00 00 00 00 ] scsi_status=0x0, sg_transport_status=0x0, sg_driver_status=0x0 sg_info=0x0 sg_duration=4 milliseconds resid=512 Incoming data trimmed to nothing by resid [NVMe call succeeded: result=0x00000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ ... ] SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02) Critical Warning: 0x00 Temperature: - Available Spare: 0% Available Spare Threshold: 0% Percentage Used: 0% Data Units Read: 0 Data Units Written: 0 Host Read Commands: 0 Host Write Commands: 0 Controller Busy Time: 0 Power Cycles: 0 Power On Hours: 0 Unsafe Shutdowns: 0 Media and Data Integrity Errors: 0 Error Information Log Entries: 0 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Temperature Sensor 1: - Temperature Sensor 2: - Temperature Sensor 3: - Temperature Sensor 4: - Temperature Sensor 5: - Temperature Sensor 6: - Temperature Sensor 7: - Temperature Sensor 8: - Thermal Temp. 1 Transition Count: 0 Thermal Temp. 2 Transition Count: 0 Thermal Temp. 1 Total Time: 0 Thermal Temp. 2 Total Time: 0 [NVMe call: opcode=0x02, size=0x0040, nsid=0xffffffff, cdw10=0x000f0001] >>>> do_scsi_cmnd_io: sg_io_ver=3 [<vendor specific>: e4 40 00 02 01 00 00 00 00 00 00 00 00 00 00 00 ] scsi_status=0x0, sg_transport_status=0x0, sg_driver_status=0x0 sg_info=0x0 sg_duration=0 milliseconds resid=0 Incoming data, len=64: 00 50 00 00 00 00 00 00 01 00 b0 00 3c 00 00 00 01 10 00 00 08 00 00 00 00 00 00 00 00 00 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [NVMe call succeeded: result=0x00000000 00 50 00 00 00 00 00 00 01 00 b0 00 3c 00 00 00 01 P..........<.... 10 00 00 08 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ ... ] Error Information (NVMe Log 0x01, 1 of 1 entries) Num ErrCount SQId CmdId Status PELoc LBA NSID VS 0 72057594037928016 45056 0x3c00 0x0000 0x100 524288 0 -
Change History (4)
comment:1 by , 20 months ago
| Keywords: | nvme added |
|---|---|
| Milestone: | → undecided |
comment:2 by , 20 months ago
| Resolution: | → fixed |
|---|---|
| Status: | new → closed |
I can confirm i had 7.2 and the device is sntasmedia.
Problem is resolved with smartctl 7.3
Thank you!
comment:3 by , 20 months ago
| Resolution: | fixed |
|---|---|
| Status: | closed → reopened |
Reopen to change resolution.
comment:4 by , 20 months ago
| Keywords: | usb added |
|---|---|
| Milestone: | undecided → Release 7.3 |
| Resolution: | → duplicate |
| Status: | reopened → closed |
See ticket #1221.
Note:
See TracTickets
for help on using tickets.
This should not happen with a proper drive database file from 7.2 branch. Please check which
VERSIONof thedrivedb.hfile is used on your system. It is usually located in/usr/lib/smartmontoolsor/var/lib/smartmontools.Please report the USB-Id of the device.
If this device actually supports
-d sntasmediadevice type, smartctl 7.3 is required.