Add to drivedb Western Digital WDC WD6000HLHX

[privatedev]

Note: whilst output below states that this drive is in drivedb 7.3/5440, a search of that file does not find a matching entry for "WD6000HLHX". As such, scan reports device as "scsi" when it appears to be "sat". "Smartctl -d scsi -i" returns incomplete Smart data whereas "smartctl -d sat -i" retuens complete smart data.

smartctl -x /dev/sda
smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.14.0-162.12.1.el9_1.x86_64] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org

START OF INFORMATION SECTION

Model Family: Western Digital VelociRaptor
Device Model: WDC WD6000HLHX-01JJPV0
Serial Number: WD-WXM1EA0KZM04
LU WWN Device Id: 5 0014ee 057f16a1e
Firmware Version: 04.05G04
User Capacity: 600,127,266,816 bytes [600 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 10000 rpm
Device is: In smartctl database 7.3/5440
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 6.0 Gb/s
Local Time is: Sun Feb 12 02:06:26 2023 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM level is: 254 (maximum performance), recommended: 128
APM level is: 128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

START OF READ SMART DATA SECTION

SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x84) Offline data collection activity

was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.

Self-test execution status: ( 0) The previous self-test routine completed

without error or no self-test has ever
been run.

Total time to complete Offline
data collection: ( 8160) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.

Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.

SMART capabilities: (0x0003) Saves SMART data before entering

power-saving mode.
Supports SMART auto save timer.

Error logging capability: (0x01) Error logging supported.

General Purpose Logging supported.

Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 87) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303d) SCT Status supported.

SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE

1 Raw_Read_Error_Rate POSR-K 100 253 051 - 0
3 Spin_Up_Time POS--K 100 253 021 - 0
4 Start_Stop_Count -O--CK 100 100 000 - 2
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 100 253 000 - 0
9 Power_On_Hours -O--CK 100 100 000 - 14

10 Spin_Retry_Count -O--CK 100 253 000 - 0
11 Calibration_Retry_Count -O--CK 100 253 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 2

192 Power-Off_Retract_Count -O--CK 200 200 000 - 0
193 Load_Cycle_Count -O--CK 200 200 000 - 1
194 Temperature_Celsius -O---K 118 117 000 - 32
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0

_ K auto-keep

| C event count

_ R error rate

| S speed/performance

_ O updated online

| P prefailure warning

General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb5 GPL,SL VS 1 Device vendor specific log
0xb6 GPL VS 1 Device vendor specific log
0xb7 GPL,SL VS 1 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 24 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 5

CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register

Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 5 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 44 01 00 00 00 00 00 30 a0 00 Error: ABRT

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.276 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.275 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.275 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.275 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.274 SMART WRITE LOG

Error 4 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 44 01 00 00 00 00 00 30 a0 00 Error: ABRT

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.275 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.275 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.275 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.274 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.160 SMART WRITE LOG

Error 3 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 44 01 00 00 00 00 00 30 a0 00 Error: ABRT

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.275 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.275 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.274 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.160 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.046 SMART WRITE LOG

Error 2 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 44 01 00 00 00 00 00 30 a0 00 Error: ABRT

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.275 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.274 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.160 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.046 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:14.932 SMART WRITE LOG

Error 1 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 30 a0 00 Error: ABRT

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.274 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.160 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:15.046 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:14.932 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f be a0 00 00:00:14.813 SMART WRITE LOG

SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1

SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS

1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing

Selective self-test flags (0x0):

After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
Device State: Active (0)
Current Temperature: 32 Celsius
Power Cycle Min/Max Temperature: 23/33 Celsius
Lifetime Min/Max Temperature: 23/33 Celsius
Under/Over Temperature Limit Count: 0/0

SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (418)

Index Estimated Time Temperature Celsius

419 2023-02-11 18:09 32 *
420 2023-02-11 18:10 32 *
421 2023-02-11 18:11 32 *
422 2023-02-11 18:12 ? -
423 2023-02-11 18:13 23
424 2023-02-11 18:14 23
425 2023-02-11 18:15 24 *
426 2023-02-11 18:16 24 *
427 2023-02-11 18:17 25
428 2023-02-11 18:18 25
429 2023-02-11 18:19 26 *
430 2023-02-11 18:20 27
... ..( 3 skipped). ..
434 2023-02-11 18:24 27
435 2023-02-11 18:25 28 *
436 2023-02-11 18:26 28 *
437 2023-02-11 18:27 28 *
438 2023-02-11 18:28 29
... ..( 3 skipped). ..
442 2023-02-11 18:32 29
443 2023-02-11 18:33 30 *
... ..( 32 skipped). .. *
476 2023-02-11 19:06 30 *
477 2023-02-11 19:07 31

0 2023-02-11 19:08 31
1 2023-02-11 19:09 31
2 2023-02-11 19:10 32 *
3 2023-02-11 19:11 32 *
4 2023-02-11 19:12 33

... ..( 3 skipped). ..

8 2023-02-11 19:16 33
9 2023-02-11 19:17 32 *

... ..( 37 skipped). .. *

47 2023-02-11 19:55 32 *
48 2023-02-11 19:56 31
49 2023-02-11 19:57 32 *
50 2023-02-11 19:58 32 *
51 2023-02-11 19:59 31

... ..( 5 skipped). ..

57 2023-02-11 20:05 31
58 2023-02-11 20:06 32 *
59 2023-02-11 20:07 31

... ..( 3 skipped). ..

63 2023-02-11 20:11 31
64 2023-02-11 20:12 32 *

... ..( 21 skipped). .. *

86 2023-02-11 20:34 32 *
87 2023-02-11 20:35 31
88 2023-02-11 20:36 32 *
89 2023-02-11 20:37 32 *
90 2023-02-11 20:38 31

... ..( 28 skipped). ..
119 2023-02-11 21:07 31
120 2023-02-11 21:08 32 *
... ..( 13 skipped). .. *
134 2023-02-11 21:22 32 *
135 2023-02-11 21:23 31
136 2023-02-11 21:24 31
137 2023-02-11 21:25 31
138 2023-02-11 21:26 32 *
139 2023-02-11 21:27 32 *
140 2023-02-11 21:28 31
... ..( 23 skipped). ..
164 2023-02-11 21:52 31
165 2023-02-11 21:53 32 *
... ..( 19 skipped). .. *
185 2023-02-11 22:13 32 *
186 2023-02-11 22:14 31
187 2023-02-11 22:15 32 *
188 2023-02-11 22:16 31
... ..( 21 skipped). ..
210 2023-02-11 22:38 31
211 2023-02-11 22:39 32 *
... ..( 13 skipped). .. *
225 2023-02-11 22:53 32 *
226 2023-02-11 22:54 31
... ..( 22 skipped). ..
249 2023-02-11 23:17 31
250 2023-02-11 23:18 32 *
... ..( 17 skipped). .. *
268 2023-02-11 23:36 32 *
269 2023-02-11 23:37 31
... ..( 15 skipped). ..
285 2023-02-11 23:53 31
286 2023-02-11 23:54 32 *
287 2023-02-11 23:55 31
288 2023-02-11 23:56 32 *
... ..( 16 skipped). .. *
305 2023-02-12 00:13 32 *
306 2023-02-12 00:14 31
... ..( 18 skipped). ..
325 2023-02-12 00:33 31
326 2023-02-12 00:34 32 *
... ..( 36 skipped). .. *
363 2023-02-12 01:11 32 *
364 2023-02-12 01:12 33
... ..( 10 skipped). ..
375 2023-02-12 01:23 33
376 2023-02-12 01:24 32 *
... ..( 21 skipped). .. *
398 2023-02-12 01:46 32 *
399 2023-02-12 01:47 33
... ..( 9 skipped). ..
409 2023-02-12 01:57 33
410 2023-02-12 01:58 32 *
411 2023-02-12 01:59 32 *
412 2023-02-12 02:00 33
413 2023-02-12 02:01 33
414 2023-02-12 02:02 32 *
... ..( 3 skipped). .. *
418 2023-02-12 02:06 32 *

SCT Error Recovery Control:

Read: 70 (7.0 seconds)

Write: 70 (7.0 seconds)

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x000a 2 1 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x8000 4 28444 Vendor specific