# smartctl -q noserial -x /dev/sda
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.17.10-1-ARCH] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: Hitachi HUA5C3030ALA640
Firmware Version: MEAOA800
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5700 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Jul 28 12:13:25 2018 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Disabled
Rd look-ahead is: Enabled
Write cache is: Disabled
DSN feature is: Unavailable
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Unknown
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
Warning: This result is based on an Attribute check.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x04) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (36068) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 601) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0
2 Throughput_Performance P-S--- 134 134 054 - 109
3 Spin_Up_Time POS--- 117 117 024 - 596 (Average 600)
4 Start_Stop_Count -O--C- 100 100 000 - 343
5 Reallocated_Sector_Ct PO--CK 001 001 005 NOW 2
7 Seek_Error_Rate PO-R-- 100 100 067 - 0
8 Seek_Time_Performance P-S--- 124 124 020 - 36
9 Power_On_Hours -O--C- 093 093 000 - 49023
10 Spin_Retry_Count PO--C- 100 100 060 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 157
192 Power-Off_Retract_Count -O--CK 099 099 000 - 2145
193 Load_Cycle_Count -O--C- 099 099 000 - 2145
194 Temperature_Celsius -O---- 200 200 000 - 30 (Min/Max 11/70)
196 Reallocated_Event_Count -O--CK 100 100 000 - 2
197 Current_Pending_Sector -O---K 001 001 000 - 19613
198 Offline_Uncorrectable ---R-- 100 100 000 - 0
199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 3
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x03 GPL R/O 1 Ext. Comprehensive SMART error log
0x04 GPL R/O 7 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x20 GPL R/O 1 Streaming performance log [OBS-8]
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Device Error Count: 3340 (device log contains only the most recent 4 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 3340 [3] occurred at disk power-on lifetime: 48992 hours (2041 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 05 00 00 cd 3d dc 83 0d 00 Error: UNC 5 sectors at LBA = 0xcd3ddc83 = 3443383427
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 cd 3d dc 80 40 00 1d+02:39:29.734 READ DMA EXT
25 00 00 00 08 00 00 cd 3d dc 78 40 00 1d+02:39:29.733 READ DMA EXT
25 00 00 00 08 00 00 cd 3d dc 70 40 00 1d+02:39:29.733 READ DMA EXT
25 00 00 00 08 00 00 cd 3d dc 68 40 00 1d+02:39:29.732 READ DMA EXT
25 00 00 00 08 00 00 cd 3d dc 60 40 00 1d+02:39:29.732 READ DMA EXT
Error 3339 [2] occurred at disk power-on lifetime: 48992 hours (2041 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 7d 00 00 cd 3d dc 83 0d 00 Error: UNC 125 sectors at LBA = 0xcd3ddc83 = 3443383427
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 01 00 00 00 cd 3d dc 00 40 00 1d+02:39:26.259 READ DMA EXT
25 00 00 01 00 00 00 cd 3d db 00 40 00 1d+02:39:26.255 READ DMA EXT
25 00 00 01 00 00 00 cd 3d da 00 40 00 1d+02:39:26.252 READ DMA EXT
25 00 00 01 00 00 00 cd 3d d9 00 40 00 1d+02:39:26.249 READ DMA EXT
25 00 00 01 00 00 00 cd 3d d8 00 40 00 1d+02:39:26.246 READ DMA EXT
Error 3338 [1] occurred at disk power-on lifetime: 48979 hours (2040 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 03 00 00 75 fe 83 dd 05 00 Error: UNC 3 sectors at LBA = 0x75fe83dd = 1979614173
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 75 fe 83 d8 40 00 14:31:15.847 READ DMA EXT
25 00 00 00 08 00 00 75 fe 83 d8 40 00 14:31:12.292 READ DMA EXT
25 00 00 00 08 00 00 75 fe 83 d0 40 00 14:31:12.291 READ DMA EXT
25 00 00 00 08 00 00 75 fe 83 c8 40 00 14:31:12.291 READ DMA EXT
25 00 00 00 08 00 00 75 fe 83 c0 40 00 14:31:12.291 READ DMA EXT
Error 3337 [0] occurred at disk power-on lifetime: 48979 hours (2040 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 03 00 00 75 fe 83 dd 05 00 Error: UNC 3 sectors at LBA = 0x75fe83dd = 1979614173
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 75 fe 83 d8 40 00 14:31:12.292 READ DMA EXT
25 00 00 00 08 00 00 75 fe 83 d0 40 00 14:31:12.291 READ DMA EXT
25 00 00 00 08 00 00 75 fe 83 c8 40 00 14:31:12.291 READ DMA EXT
25 00 00 00 08 00 00 75 fe 83 c0 40 00 14:31:12.291 READ DMA EXT
25 00 00 00 08 00 00 75 fe 83 b8 40 00 14:31:12.290 READ DMA EXT
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: SMART Off-line Data Collection executing in background (4)
Current Temperature: 30 Celsius
Power Cycle Min/Max Temperature: 28/46 Celsius
Lifetime Min/Max Temperature: 11/70 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -40/70 Celsius
Temperature History Size (Index): 128 (64)
Index Estimated Time Temperature Celsius
65 2018-07-28 10:06 31 ************
... ..(126 skipped). .. ************
64 2018-07-28 12:13 31 ************
SMART WRITE LOG does not return COUNT and LBA_LOW register
SCT (Get) Error Recovery Control command failed
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 1) ==
0x01 0x008 4 157 --- Lifetime Power-On Resets
0x01 0x010 4 49023 --- Power-on Hours
0x01 0x018 6 154994154345 --- Logical Sectors Written
0x01 0x020 6 897377010 --- Number of Write Commands
0x01 0x028 6 395957567089 --- Logical Sectors Read
0x01 0x030 6 4680524246 --- Number of Read Commands
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 48896 --- Spindle Motor Power-on Hours
0x03 0x010 4 48896 --- Head Flying Hours
0x03 0x018 4 2145 --- Head Load Events
0x03 0x020 4 2 --- Number of Reallocated Logical Sectors
0x03 0x028 4 4248 --- Read Recovery Attempts
0x03 0x030 4 0 --- Number of Mechanical Start Failures
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 3330 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 229 --- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 30 --- Current Temperature
0x05 0x010 1 37 N-- Average Short Term Temperature
0x05 0x018 1 44 N-- Average Long Term Temperature
0x05 0x020 1 70 --- Highest Temperature
0x05 0x028 1 11 --- Lowest Temperature
0x05 0x030 1 66 N-- Highest Average Short Term Temperature
0x05 0x038 1 25 N-- Lowest Average Short Term Temperature
0x05 0x040 1 61 N-- Highest Average Long Term Temperature
0x05 0x048 1 25 N-- Lowest Average Long Term Temperature
0x05 0x050 4 341100 --- Time in Over-Temperature
0x05 0x058 1 60 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 0 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 159709 --- Number of Hardware Resets
0x06 0x010 4 10116 --- Number of ASR Events
0x06 0x018 4 3 --- Number of Interface CRC Errors
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0009 2 9 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 8 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
r5102, r5103.